Topics Topics Edit Profile Profile Help/Instructions Help Member List Member List  
Search Last 1|3|7 Days Search Search Tree View Tree View  

TANKS!

S2 9.1 Class Bulletin Board » Technical Assistance, Fixes & Advice » TANKS! « Previous Next »

  Thread Last Poster Posts Pages Last Post
  Start New Thread        

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Mike Bergmann
Unregistered guest

Rating: N/A
Votes: 0 (Vote!)

Posted on Saturday, July 17, 2004 - 03:16 pm:   Edit PostDelete PostView Post/Check IPPrint Post   Move Post (Moderator/Admin Only)Ban Poster IP (Moderator/Admin only)

I removed the fuel tank the other day. As expected, the bottom of the tank was heavily corroded and fouled. I removed all of the dirt, etc. with a power wire brush, and found about 8 areas of deep pitting which appeared to be at least 3/4 of the way through the bottom of hte tank.

I used the West System aluminum etching kit to clean the bottom of the tank, and laminated 3 layers of 6 oz. fiberglass cloth over the bottom using West epoxy. The whole process took about 2 hours.

I hate to sound like a broken record, but I want to urge everyone with an older boat to check the tanks ASAP. My boat spends some time in salt water, so the tanks in the fresh-water boats are probably not as bad. Anyone with an '83 or '84 in salt water should be very concerned about this.
Top of pagePrevious messageNext messageBottom of page Link to this message

Mike Bergmann
Unregistered guest

Rating: N/A
Votes: 0 (Vote!)

Posted on Saturday, July 10, 2004 - 09:42 pm:   Edit PostDelete PostView Post/Check IPPrint Post   Move Post (Moderator/Admin Only)Ban Poster IP (Moderator/Admin only)

Ed & Julie

Thanks for the info. If I find leaks in my fuel tank I will try this stuff - I have had no luck finding a replacement fuel tank online in case mine is beyond repair.

Mike Bergmann
Top of pagePrevious messageNext messageBottom of page Link to this message

Ed and Julie Gully
New member
Username: Goldenomen

Post Number: 13
Registered: 05-2001

Rating: N/A
Votes: 0 (Vote!)

Posted on Friday, July 09, 2004 - 11:03 am:   Edit PostDelete PostView Post/Check IPPrint Post   Move Post (Moderator/Admin Only)Ban Poster IP (Moderator/Admin only)

Mike; I have found a product that will seal a tank that has pin holes in it. It is made by POR15 and comes as a kit to clean the tank and then seal it.

por15.com
Ed Gully
Top of pagePrevious messageNext messageBottom of page Link to this message

Mike Bergmann
Unregistered guest

Rating: N/A
Votes: 0 (Vote!)

Posted on Monday, June 28, 2004 - 10:31 pm:   Edit PostDelete PostView Post/Check IPPrint Post   Move Post (Moderator/Admin Only)Ban Poster IP (Moderator/Admin only)

I posted a message a few days ago about a badly corroded water tank (see "Fresh Water Tank"). I now find that the fuel tank also rests directly on the wood sole under the berth. It is likely that the fuel tank is also corroded.

I found a very informative article on the web at http://www.powerandmotoryacht.com/maintenance/0402fueltanks/. I urge everyone to read this and think about your tanks.

I plan to empty out my fuel tank as soon as possible and then remove it from the boat. If the bottom corrosion is not too bad, I will clean it thoroughly with a power wire brush and apply a few layers of fiberglass and West System epoxy.

I found a good replacement for the water tank at www.boatdepot.com. The Ronco "B394" is a good fit under the starboard berth and is slightly larger than the original tank. You will have to do some minor modifications to fit this tank, and you will have to purchase the fitting relocation kit. The overall cost will run around $300.

I plan to bed this new tank on a 1/2" layer of closed-cell styrofoam insulation, and install two hold-downs at each end.

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and moderators may post messages here.
Password:
Options: Enable HTML code in message
Automatically activate URLs in message
Action:

Administration Administration Log Out Log Out   Previous Page Previous Page Next Page Next Page